This Circuit will explain the PLL unit and the VCO (Voltage Controlled Oscillator) which will create the FM modulated RF signal up to 400mW. the schematic to follow my function description. The main oscillator is based around the transistor Q1. This oscillator is called Colpitts oscillator and it is voltage controlled to achieve FM frequency modulation) and PLL control.
Q1 should be a HF transistor to work well, but in this case I have used a cheap and common BC817 transistor which works great. The oscillator needs a LC tank to oscillate properly. In this case the LC tank consist of L1 with the varicap D1 and the two capacitor (C4, C5) at the base-emitter of the transistor. The value of C1 will set the VCO range.
The large value of C1 the wider will the VCO range be. Since the capacitance of the varicap (D1) is dependent of the voltage over it, the capacitance will change with changed voltage. When the voltage change, so will the oscillatingfrequency. In this way you achieve a VCO function. You can use many different varicap diod to get it working. In my case I use a varicap (SMV1251) which has a wide range 3-55pF to secure the VCO range (88 to 108MHz).Inside the dashed blue box you will find the audio modulation unit. This unit also include a second varicap (D2). This varicap is biased with a DC voltage about 3-4 volt DC. This varcap is also included in the LC tank by a capacitor (C2) of 3.3pF. The input audio will passes the capacitor (C15) and be added to the DC voltage. Since the input audio voltage change in amplitude, the total voltage over the varicap (D2) will also change. As an effect of this the capacitance will change and so will the LC tank frequency.
You have a Frequency Modulation of the carrier signal. The modulation depth is set by the input amplitude. The signal should be around 1Vpp. Just connect the audio to negative side of C15. Now you wonder why I don't use the first varicap (D1) to modulate the signal? I could do that if the frequency would be fixed, but in this project the frequency range is 88 to 108MHz.
If you look at the varicap curve to the left of the schematic. You can easily see that the relative capacitance change more at lower voltage than it does at higher voltage. Imagine I use an audio signal with constant amplitude. If I would modulated the (D1)varicap with this amplitude the modulation depth would differ depending on the voltage over the varicap (D1). Remember that the voltage over varicap (D1) is about 0V at 88MHz and +5V at 108MHz. By use two varicap (D1) and (D2) I get the same modulation depth from 88 to 108MHz.
Now, look at the right of the LMX2322 circuit and you find the reference frequency oscillator VCTCXO. This oscillator is based on a very accurate VCTCXO (Voltage Controlled Temperature controlled Crystal Oscillator) at 16.8MHz. Pin 1 is the calibration input. The voltage here should be 2.5 Volt. The performance of the VCTCXO crystal in this construction is so good that you do not need to make any reference tuning.
A small portion of the VCO energy is feed back to the PLL circuit through resistor (R4) and (C16). The PLL will then use the VCOfrequency to regulate the tuning voltage. At pin 5 of LMX2322 you will find a PLL filter to form the (Vtune) which is the regulating voltage of the VCO. The PLL try to regulate the (Vtune) so the VCO oscillatorfrequency is locked to desired frequency. You will also find the TP (test Point) here.
The last part we haven't discussed is the RF power amplifier (Q2). Some energy from the VCO is taped by (C6) to the base of the (Q2). Q2 should be a RF transistor to obtain best RF amplification. To use a BC817 here will work, but not good.
The emitter resistor (R12 and R16) set the current through this transistor and with R12, R16 = 100 ohm and +9V power supply you will easy have 150mW of output power into 50 ohm load. You can lower the resistors (R12, R16) to get high power, but please don't overload this poor transistor, it will be hot and burn up… Current consumption of VCO unit = 60 mA @ 9V.
Printed Circuit Board (PCB.pdf)This is how the real board should look when you are going to solder the components.
It is a board made for surface mounted components, so the cuppar is on the top layer.
Parts List
100 = R7, R12, R16
330 = R4
1k = R1, R2, R3, R10
3.3k = R11
10k = R5, R6, R14, R17
20k = R13
43k = R9
100k = R8, R15
3.3pF = C2, C16
15pF = C4, C6
22pF = C5
1nF = C1, C3, C8, C17, C22, C23
100nF = C7, C9, C11, C12, C13, C14, C19, C20
2.2uF = C15, C18
220uF = C10, C21
L1 = 3 turns diam 6.5mm (Everything from 6 to 7 mm will work good!)
L2, L3, L4 = 10uH
D1, D2 = SMV1251
Q1 = BC817-25
Q2 = BFG193
X1 = 16.800 MHz VCTCXO Reference oscillator
V1 = 78L05
IC1 = LMX2322
Source
